What Size Reservoir Do You Need for a Hydroponic System?
Share
The short answer: size your hydroponic reservoir by the plants it feeds. As a rule of thumb, allow about 2 to 4 litres per plant for small crops such as lettuce, herbs and seedlings, 4 to 6 litres per plant for medium crops such as chillies, peppers and cucumbers, and 8 to 10 litres or more per plant for large, vining crops such as tomatoes. Then add a buffer. A bigger reservoir costs a little more to fill, but it holds pH, nutrient strength (EC) and temperature far more steadily than a small one, so you spend less time correcting it. If in doubt between two sizes, pick the larger.
In this article
- Why does reservoir size matter in hydroponics?
- How many litres per plant do you need?
- Does the type of hydroponic system change the size?
- How do you calculate the right reservoir size?
- Is a bigger reservoir always better?
- How do you keep a reservoir topped up?
- FAQ
Why does reservoir size matter in hydroponics?
Your reservoir is the only source of water and food for every plant in the system, and it changes constantly. Plants drink water and take up nutrients at different rates, so pH and EC drift between checks. The University of Missouri Extension notes that nutrient solutions must be constantly measured and adjusted, because pH and EC change as plants and microbes use water and nutrients. It puts the optimum pH for most hydroponic crops at 5.5 to 6.5.
Volume is your shock absorber. In a 10 litre tank feeding six thirsty plants, a warm day can drop the level and concentrate the nutrients noticeably in a few hours. In an 80 litre tank, the same water loss is a small percentage, so the readings move slowly and you have time to react.
Small volumes also warm and cool quickly, and the same Missouri guide points out that warmer water holds less dissolved oxygen. Most growers aim to keep the solution around 18 to 21°C. A larger volume is much easier to hold in that range.
How many litres per plant do you need?
These are practical starting points rather than hard rules. Treat them as the minimum, then add a buffer of 25 to 50% so you are not refilling every day.
| Plant size | Typical crops | Litres per plant (minimum) | Example: 6 plants |
|---|---|---|---|
| Small | Lettuce, basil, mint, pak choi, seedlings | 2 to 4 L | 12 to 24 L, plus buffer |
| Medium | Chillies, sweet peppers, cucumbers, strawberries | 4 to 6 L | 24 to 36 L, plus buffer |
| Large | Tomatoes, aubergines, climbing beans | 8 to 10 L or more | 48 to 60 L, plus buffer |
Water use climbs as plants grow, so size for the plants at full size, not on the day you plant them.
Unbreakable black plastic nutrient tank measuring 76 x 49 x 30cm. The low profile slides under a bench or into the base of a tent, and the black plastic blocks light to help stop algae.
Does the type of hydroponic system change the size?
Yes. The per-plant figures above are a good guide for recirculating systems, but each system type has its own quirks.
- Deep water culture (DWC): the roots sit in the reservoir, so the bucket is the reservoir. Around 19 litres is a sensible floor for one plant, and 30 litres or more gives noticeably steadier conditions for a large plant.
- Recirculating DWC and NFT: a central tank feeds several sites. Add up the per-plant needs, then allow for the water sitting in the channels or pipework while the pump runs. If the pump stops, that water drains back, so the tank must be able to hold it without overflowing.
- Ebb and flow (flood and drain): the tank must hold enough to flood the tray to the right depth while still keeping the pump covered. Measure the tray (length x width x flood depth) and add 25 to 35% on top.
- Drip systems: work out roughly how much the plants use per day, multiply by the number of days you want between top-ups, then add 30 to 50% as a safety margin.
How do you calculate the right reservoir size?
A quick three-step method works for most home setups:
- Count the plants and pick their size band from the table above. Six chilli plants at 5 litres each is 30 litres.
- Add the water held in the system. Channels, trays and pipes can hold several litres that leave the tank while the pump runs.
- Add a 25 to 50% buffer and round up to the next tank size. 30 litres plus pipework plus buffer points to a 60 to 80 litre tank.
Leave headroom at the top, too. Filling a tank to around 85 to 90% of its capacity leaves room for drain-back and makes it easier to mix in nutrients without splashing.
Is a bigger reservoir always better?
Bigger is more stable, but there are trade-offs to weigh:
- Cost per change: every full change means discarding the old solution and mixing fresh nutrients for the whole volume. Our guide on how often to change hydroponic nutrient solution explains when to do a full swap.
- Weight and space: water weighs about 1kg per litre, so a full 80 litre tank is around 80kg. Place it before you fill it and make sure the floor can take it.
- Temperature control: a large tank is slower to heat or cool. That is mostly a benefit, but if it does drift, it takes longer to bring back. See our article on reservoir temperature, chillers and heaters for more.
For larger setups, or for storing pre-treated water ready for top-ups, a flexible tank gives a lot of volume without a lot of floor clutter.
A tool-free flexible tank with four support poles and a tap. Use it as a nutrient tank indoors or to store water for top-ups, then fold it away when you are done.
How do you keep a reservoir topped up?
Between full changes you will need to replace the water your plants drink. Check EC before you top up, because it tells you what to add:
- EC above target: plants are drinking more water than food, so top up with plain, pH-adjusted water.
- EC on target: top up with a weaker nutrient mix.
- EC below target: plants are feeding hard, so top up with full-strength solution.
A useful habit is to do a full change once the total you have topped up equals the volume of the tank, as the mix will have drifted a long way from what you started with by then. Check pH after every top-up and bring it back to 5.5 to 6.5.
Water and shock resistant, with a memory for the last 10 readings so you can track how fast your reservoir drifts. Simple one-button calibration.
If you are away often, an automatic float valve can keep the level steady by feeding water in from a larger header tank as the plants drink.
Automatically maintains the water level in your reservoir, so you are not checking and topping up by hand every day.
Frequently asked questions
What size reservoir do I need for a small hydroponic system?
For a handful of herbs or salad plants, 15 to 30 litres is usually plenty. Allow 2 to 4 litres per small plant, then add a buffer so you are not refilling daily.
Can a hydroponic reservoir be too big?
Not for the plants, which benefit from the stability. The downsides are practical: more nutrients per full change, more weight, and more space. If the tank is so big that you would only ever half-fill it, step down a size.
How often should I top up my reservoir?
As often as the level drops noticeably, which can be daily for mature plants in warm weather. A larger tank or an automatic float valve stretches the gap between top-ups.
What temperature should my reservoir be?
Around 18 to 21°C suits most crops. Warmer water holds less dissolved oxygen, which stresses roots, while very cold water slows growth.
Why is a black or opaque tank recommended?
Light reaching nutrient solution lets algae grow, which competes for nutrients and oxygen. An opaque tank with a lid keeps the solution dark.
Find the right tank for your setup
Browse our nutrient tanks, flexi tanks and water butts, from compact low-profile reservoirs to large-volume storage.
Shop tanks and reservoirs âFast UK delivery, with Click and Collect from our County Durham store.