Rockwool propagation cubes used for starting coriander seeds hydroponically

How to Grow Coriander Hydroponically: A Complete UK Guide

Yes, you can grow coriander hydroponically indoors, and for most UK growers it is actually more reliable than growing it in soil outdoors, where it often bolts to seed within weeks of a warm spell. The quickest route is a passive Kratky or NFT system running at EC 1.2 to 1.8 mS/cm and pH 5.8 to 6.4, with 12 to 14 hours of light a day and the reservoir kept below about 22°C. Coriander grows fast from seed and never develops a large root system, which suits hydroponics well: you can expect a full cut-and-come-again harvest within 4 to 5 weeks, and because you control temperature and daylight indoors, you sidestep the single biggest reason coriander fails outdoors in the UK, bolting in a hot, dry spell. Below is exactly how to set a system up, which pH and EC targets to aim for, and how to keep plants harvestable for months rather than weeks.

In This Article

What's the Best Hydroponic System for Growing Coriander?

Coriander has a light, fast-growing root system and is usually sown directly into its final growing position (a net pot or a rockwool cube) rather than transplanted as a seedling, since disturbing young roots tends to set the plant back. That makes it flexible across several hydroponic setups, but each suits a different kind of grower.

System Best for Pros Watch out for
Kratky (passive) A single tray of coriander for home kitchen use No pump, no electricity, very simple to set up Nutrient strength concentrates as the reservoir level drops, so EC needs checking
NFT Continuous, staggered sowing for a steady supply Constant fresh nutrient film, good root oxygenation, easy to add more channels Needs a pump running continuously, a blocked channel dries roots quickly
Media bed (rockwool or coco, hand-fed or drip) Growing coriander on to a bushier, longer-lived plant Holds the root zone steady, forgiving of small pH or EC swings Drains slowly, so overwatering is the main risk

For most home growers, an NFT system is the easiest way to keep a rolling supply going, since you can sow a fresh tray every couple of weeks without disturbing the plants already cropping.

What pH and EC Does Coriander Need Hydroponically?

Oklahoma State University's hydroponic EC and pH guide does not list coriander specifically, but it does cover parsley, coriander's close relative in the same carrot family (Apiaceae), at an EC of 1.8 to 2.2 mS/cm and pH 6.0 to 6.5. In practice, most hydroponic growers run coriander a little lighter than parsley, since its leaves are more delicate and it is grown for fast, repeated cutting rather than a long-lived crop. A good starting range is EC 1.2 to 1.8 mS/cm and pH 5.8 to 6.4, adjusted up slightly if growth looks pale or weak.

Essentials pH meter for checking hydroponic reservoir pH
Measuring
Essentials pH Meter

Waterproof pH meter with a memory of past readings, so you can track drift in a coriander reservoir over several weeks.

£58.00 Shop now →
Essentials EC meter for checking hydroponic nutrient strength
Measuring
Essentials EC Meter

Checks nutrient strength directly in your reservoir, which matters for Kratky setups where EC rises as the water level drops.

£58.00 Shop now →

How Do You Start Coriander Seeds for a Hydroponic System?

The Royal Horticultural Society notes that coriander seeds are large and easy to handle, and should be sown roughly 5cm apart. Germination "takes one to three weeks, depending on outdoor temperatures", so in a stable, warm grow tent you are usually at the faster end of that range, often closer to a week to ten days. Sow two or three seeds directly into a rockwool cube rather than a seed tray, then thin to the strongest single seedling once true leaves appear, so the roots are never disturbed by transplanting.

Cultiwool rockwool propagation cubes for starting coriander seeds
Propagation
Cultiwool Rockwool Cubes

Sow coriander seed directly into these and drop the whole cube into a net pot once roots show, with no transplant shock.

From £0.39 Shop now →

How Do You Stop Hydroponic Coriander From Bolting?

Bolting, where the plant switches from producing leaves to shooting up a flower stem, is the single biggest complaint about growing coriander, and both the RHS and the University of Maryland Extension agree on the trigger: heat. The RHS puts it plainly: "plants tend to bolt in hot, dry weather, so if you're growing coriander for its leaves in summer, sow in a cooler location out of midday sun." The University of Maryland Extension adds that humidity plays a role too, and that pinching off flower stems as they appear will extend how long you can keep harvesting leaves from a plant that is starting to turn.

Growing indoors under hydroponic conditions removes most of that risk, since you control the temperature directly rather than relying on the weather. Keep the air and reservoir below about 22 to 24°C, avoid letting the lights push the tent hotter than that, and use succession sowing, a fresh tray every two to three weeks, so you are never relying on one batch of plants to keep producing indefinitely. When an older tray does start to bolt, treat it as a seed crop rather than a failure: left to mature, the flowers will set coriander seed you can collect and use in the kitchen.

How Do You Feed Coriander From Seedling to Harvest?

Coriander is a light feeder compared with fruiting crops, so a general-purpose seedling and leafy-crop formula works well through its entire 4 to 5 week life, rather than switching formulas partway through. Start at the lower end of the EC range once true leaves appear, and only raise it if growth stalls or leaves turn pale. The RHS describes coriander as a cut-and-come-again crop once plants reach 10 to 15cm tall, which lines up with the University of Maryland Extension's guidance to begin harvesting once plants hit around 15cm (6 inches): cut the outer leaves and leave the centre growing point intact so the plant keeps producing.

Growth Technology Formulex nutrient for seedlings and leafy herbs
Feeding
Growth Technology Formulex

A gentle, chelated general-purpose feed suited to seedlings and fast-cropping leafy herbs like coriander, from first true leaves to final harvest.

£10.50 Shop now →

If you want to compare notes with another fast-cropping herb grown the same way, our guide to growing mint hydroponically indoors covers a herb with a very different growth habit (mint spreads from cuttings rather than seed, and never bolts), which is a useful contrast when you are deciding what to grow alongside your coriander.

Frequently Asked Questions

Can you grow coriander hydroponically indoors in the UK?

Yes. Coriander grows well hydroponically and indoor growing actually solves its main outdoor problem in the UK, bolting in a sudden hot spell, since you control temperature and light directly.

What's the best hydroponic system for coriander?

NFT suits most home growers best, since it is easy to run a continuous, staggered supply. A simple Kratky setup works well for a single one-off tray, and a media bed suits growers who want a bushier, longer-lived plant rather than a quick cut-and-come-again crop.

Why does my hydroponic coriander keep bolting?

Heat is almost always the cause. If the grow tent or reservoir is running above about 24°C, or the lights are too close and raising leaf temperature, the plant will switch to flowering. Keep temperatures down and sow a fresh tray every two to three weeks so bolting in one tray does not leave you without a harvest.

How long does coriander take to grow hydroponically?

Germination typically takes a week to three weeks depending on temperature, and you can start cutting leaves once plants reach 10 to 15cm tall, usually around 4 to 5 weeks after sowing in a warm, stable grow tent.

Can you regrow coriander from a supermarket bunch hydroponically?

Not reliably. Unlike mint or basil, coriander does not root well from cuttings placed in water, since it puts its energy into a central taproot rather than side shoots. It is much more reliable to grow coriander hydroponically from seed.

Do you need to feed coriander differently once it starts flowering?

No extra feed is needed. If a tray starts to bolt, it is usually more worthwhile to let it finish and collect the seed than to try to push it back into leaf production with a feed change.

Ready to Start Your Own Coriander Tray?

Get everything you need for seed starting and early feeding in one place.

Shop Propagation & Early Feeds →
Back to blog

Leave a comment

Please note, comments need to be approved before they are published.